Chapter 2-2: Know your vehicle

The “Know Your Vehicle” section of the Ontario motorcycle practice test focuses on familiarizing riders with their motorcycle’s features and controls.

Ontario Motorcycle Test - Chapter 2-2: Know your vehicle

1 / 40

What is the engine kill switch primarily designed for?

To shift gears automatically

To control the headlight beam

To lock the handlebars

To stop the engine quickly in an emergency

2 / 40

What is the purpose of the choke?

To help start a cold engine by adjusting the gasoline–air mixture

To increase braking force

To control turn signal timing

To reduce headlight brightness

3 / 40

What does the red line on a tachometer indicate?

The maximum rpm that is safe for the engine

The recommended cruising rpm

The point where the engine will stall

The minimum idle speed

4 / 40

What does the neutral indicator light show?

That the fuel tank is full

That the engine is overheating

That the transmission is in neutral gear

That the headlight is off

5 / 40

What is the purpose of the ignition switch?

To control the headlights only

To open the fuel tank

To turn the ignition system on and off

To operate the horn

6 / 40

Where is the clutch lever located?

On the right handlebar

On the left handlebar

Next to the speedometer

Near the right footrest

7 / 40

What should you do with a manual fuel supply valve when the vehicle is not in use?

Turn it to reserve

Set it to “start” position

Leave it fully open at all times

Turn it off to avoid a fire hazard

8 / 40

When you gear down or reduce throttle, what is one important limitation?

The motorcycle will speed up

The engine will stall immediately

The engine cannot slow the motorcycle

The brake lights will not turn on

9 / 40

Why should you apply your brakes even when using engine braking to slow down?

To increase engine temperature

To reduce wear on the tires

To signal to others that you are slowing down

To save fuel

10 / 40

What must every motorcycle or moped have regarding sound signaling?

A siren for emergencies

A bell and a whistle

A loud exhaust system

A horn that works

11 / 40

Where is the shift lever located?

On the right handlebar

On the left handlebar

Near the right footrest

Near the left footrest

12 / 40

Where is the rear brake lever usually located on a motorcycle?

On the right handlebar

On the left handlebar

Near the right footrest

Near the left footrest

13 / 40

What must you always do before driving away after using a stand?

Switch the fuel valve to reserve

Completely raise your stands

Turn off the choke

Turn off your headlight

14 / 40

Where is the throttle located?

On the left handgrip

On the right handgrip

Near the right footrest

Next to the fuel supply valve

15 / 40

Why must you know the controls well enough to reach them without taking your eyes off the road?

So you can ride faster

So you can pass the written test

So you can operate all controls by reflex in traffic

So you can adjust the mirrors while stopped at lights

16 / 40

What do you use to control the motorcycle’s direction?

The rear brake lever

The throttle

The clutch lever

The handlebars

17 / 40

What happens when you squeeze the clutch lever toward the handgrip?

The engine is turned off

The clutch is engaged

The clutch is disengaged

The brakes are applied

18 / 40

Why is it important to become familiar with your specific vehicle’s controls?

Because motorcycles and mopeds are all identical

Because only the pedals change between models

Because the same control may not be in the same place on all vehicles

Because controls are always hidden

19 / 40

What does the turn signal indicator light do?

Comes on only when braking

Flashes when the left or right turn signal is on

Stays on whenever the ignition is on

Changes color with speed

20 / 40

What does the speedometer show?

The distance traveled since last refuel

The amount of fuel remaining

The speed you are driving in kilometres per hour or miles per hour

The engine temperature

21 / 40

Why is forgetting to turn off your turn signal dangerous?

It turns off your brake light

Other drivers may pull out or turn in front of you

It wastes battery power

It reduces engine performance

22 / 40

After using the engine kill switch to stop the engine, what must you also do?

Turn on the choke

Open the fuel supply valve

Turn off the ignition switch

Apply the front brake

23 / 40

How is the shift lever operated?

By lifting or pressing it with your foot

By pulling it with a cable

By turning it with your hand

By pressing a button on the handlebar

24 / 40

How is the front brake applied?

By twisting the throttle away from you

By pressing with your right foot

By pushing the lever away from the handgrip

By squeezing the lever toward the handgrip

25 / 40

How should you use your brakes when slowing or stopping?

Use only the rear brake

Use only the front brake

Use the engine only for braking

Use the front and rear brakes together

26 / 40

What happens if the engine kill switch is in the “off” position?

The brakes will lock

The engine will not start

The turn signals will not work

The headlight will not turn on

27 / 40

What must you do before changing gears?

Apply the rear brake

Use the horn

Disengage the clutch

Turn off the ignition

28 / 40

Where is the front brake lever located?

On the left handlebar near the clutch

On the right handlebar in front of the throttle

Near the left footrest

On the frame below the seat

29 / 40

Before using the electric starter, what should you make sure of?

The engine kill switch is off

The fuel valve is turned off

The throttle is fully open

The motorcycle is in neutral and the clutch is depressed

30 / 40

On most modern motorcycles and mopeds, when do the headlight and tail light come on?

Only at night

Only when the brakes are applied

Only when the rider turns a separate switch

Automatically when the ignition is on and the engine is running

31 / 40

When is the choke normally used?

When riding at high speed

When turning off the engine

When starting a cold engine

When braking hard

32 / 40

What is the purpose of a kickstand or centre stand?

To protect the engine in a crash

To improve cornering speed

To hold the motorcycle or moped upright when it is parked

To assist with braking

33 / 40

How should the throttle behave when you let go of it?

It should lock in place for cruising

It should slowly close over a minute

It should spring back completely to the idle position

It should stay where you leave it

34 / 40

What does a manual fuel supply valve (petcock) control?

The flow of coolant to the radiator

The amount of air entering the engine

The flow of gasoline to the engine

The flow of oil to the engine

35 / 40

What is a key difference of many motorcycle and moped turn signals compared to car signals?

They often do not automatically switch off after a turn

They are always on when the engine runs

They only work for right turns

They flash only at night

36 / 40

What is the first step in learning to drive a motorcycle or moped?

Learn where the vehicle’s controls are and what they do

Memorize the owner’s manual

Practice riding in traffic immediately

Learn traffic signs and signals

37 / 40

How do you increase speed using the throttle?

Twist the throttle toward you

Push the throttle down

Pull the throttle up

Twist the throttle away from you

38 / 40

What does the tachometer show?

The battery charge level

The amount of oil in the engine

The number of engine revolutions per minute

The total distance traveled

39 / 40

How do most motorcycle electric starters operate?

You push a starter button on the right handlebar near the throttle

You turn the key fully clockwise and hold

You step on a floor-mounted pedal

You pull a lever on the left handlebar

40 / 40

What is the purpose of a reserve fuel supply on some fuel tanks?

To cool the engine

To add extra engine oil

To store brake fluid

To provide additional fuel when the main section runs dry

Your score is

This section covers the location and function of essential components such as brakes, throttle, clutch, gears, horn, and lights. Understanding how each part operates is vital for safe riding and quick responses in emergencies. The practice test may include questions about routine checks, such as tire pressure and fluid levels, to ensure your motorcycle is in optimal condition. By mastering this section, new riders build confidence in handling their vehicle and lay the groundwork for safe, responsible riding in Ontario.